We can supply both Chinese brand and foreign brand generator.
Ricardo Diesel Generator set, from 10kw to 300kw.
Cummins Diesel Generator Set, from 10kw to 800kw.
Perkins Diesel Generator, from 10kw to 800kw.
Deutz Diesel Generator, from 10kw to 120kw.
Standards:
Generator sets meets GB/TB2820 general technical specifications for Diesel Generator
set
Electric
performance for generator sets,
Rated
voltage: 480-110V
Connection
method: 3 phase, 4 wires or 1 phase 3 wires.
Rated
frequency: 50 Hz or 60 Hz
Rated speed:
1500rpm or 1800rpm
Frequency regulation:
steady state ≤-5%
Transient
state ≤±10%
Steady state
voltage regulation ≤±1%
Power factor:
0.8 lagging
Line voltage
wave from distortions:≤5
We own profession generator personal
who has strong experience
Offer 8-1000kw generator maintain
business
Supply generator machine room design
and installation project
Offer diesel generator installation,
adjust, theory instruction, and training.
Offer automatic generator from
normal, and humanization intelligent control.
Offer diesel generator machine room
noise reduction project
Supply standard
collocation
Diesel Engine , with
all accessories, fuel/air/oil filters, electric systems
Alternator
Steel structure base
or with base fuel tank
Fan, radiator, cooling
system
Flange connector
12V/24V starter and
charge alternator
Air filter, fuel
filter and oil filter
On-board control
panel, alarm and stop in condition of high water temperature, low oil pressure,
over speed, over load
MCCB air conservation
switch
12V/24V start
accumulator and batter line
Generator vibration
absorber
High-efficient muffler
Diesel Generator Deutz Diesel Generator, Ricardo Diesel Generator, Weichai Diesel Generator, Lovol Diesel Generator Weifang Huatian Diesel Engine Co., Ltd , https://www.enginepart.nl
the America, Asia,etc. The other sizes are woodworking bander RFB465,465F,465JC, 465JF,465JH,
RFB465JCF,RFB465JCH.
Suitable for straight line edge banding. OEM and ODM are available.
PLC touch screen: Delta(Taiwan) Â Â Â Â Â Electric control element:Schneider
Frequency Converter:Shihlin(Taiwan) Â Pneumatic component:Mindman and Easun(taiwan)
Feeding motor and Gear Motor:Tung Lee or CPG(taiwan)
High Speed motor:HST(Taiwan)
Function of wood edge banding machine, 465JCH
465JCH
Pre-milling
Gluing
Edge
CuttingPress
End Trim
Fine Trim
Corner Trim
Scraping
Hogging
Buffing
Parameter
Model
RFB465JCH
Panel length
≥120mm
Panel width
≥60mm
Panel thickness
10-60mm
Edgeband thickness
0.3-3mm
Feeding speed
13-22m/min
In-put voltage
380V.
In-put frequency
50HZ.3P
Total power
22KW
Required air pressure
0.6Mpa
Overall dimensions(L*W*H)
6800*900*1560mm
Functions of Woodworking Machines, Edge Banding Machines, 465JCH,
1.Pre-milling system
Pre-milling adopts double linear guide, with higher guidance accuracy and good motion stability,Â
pre-cutter Φ125mm H35mm six-tooth diamond pre-milling cutter, with high hardness and wear resistance,
longer service life.
 2. Gluing system
In gluing system, the glue box is coated with Teflon, which makes the box cleaning easier. The glue box has
the temperature maintaining function and can shorten heating time and avoid the glue carbonization. TheÂ
machine can use the high temperature EVA hot melt glue and can deliver the glue by spiral structure.Â
The glue box size is 200*150*450mm.Â
3.Feeding and edge cutting systemÂ
When the single unit feeding system can be used to load the strip (optional) and roller type edge bands and
 the edge band thickness can be 0.4~3mm. If the single work unit can not meet the working requirements,Â
the 2-10 feeding units can be selected. The edge cutting cylinder is controlled by double solenoid valves.Â
4. Press system
The precise large press wheel and glue wheel can work together to ensure the press effect. The small press
 wheel are composed of 2 upper and lower cone wheels and 1 straight wheel. The upper and lower coneÂ
wheels can ensure the good press effect. The large and small press wheels are controlled by the separate
 pressure control valve.Â
 Optional: One large wheel can be equipped with 5 small wheels.Â
5. End trimming system
Adopt the imported precision linear guider, the automatic profiling tracking and high frequency and highÂ
speed motor of 0.37kw to ensure the smooth cut surface.
6. Fine trimming system
Rough trimming motor is 0.75kw high frequency motor. The rough trimming tools are the Φ69mm four
 tooth carbide cutters with high hardness and wear resistance. The tools processing angle is 45°.Â
Optional:High-power high-frequency motor 1.1kw.Â
7. Corner trimming systemÂ
To process the round / duck mouth / right angles caused by end trimming to form a perfect round angle.
Use 0.37KW high frequency motor and R2.5,Φ70mm ,3Z carbide tools.Â
If the work piece has hinge hole or other processing holes on surface, the integrated large profile wheel is optional.Â
Match big profile wheel to process panels with hinge holes or other processing holes on surface.
8. Scrapping systemÂ
 It is used for PVC or ABS edge band less than or equal to 3mm. The system adopts high steel structure.
 Use knob to adjust the arc angle. Each group has two precise profile wheels to ensure the accuracy ofÂ
  cutting point.Â
9.Hogging system
Single lateral hogging depth can not be over 8mm. If deeper than 8mm, another lateral hogging shall beÂ
added. Either side hogging(L) or down hogging(H). It is used for direct slotting of the side plate and drawer
 bottom plate of wardrobe, and it is more convenient by reducing working procedure of panel saw.Â
10.Buffing system:
The two independent motors equipped with buffing wheels are used for cleaning and buffing after edge
 banding, easy to operate.Â
Optional: Pneumatic reciprocating buffing by motors.
11. Electric systemÂ
Each functional group is controlled by independent Delta inverter to ensure the co-movement of the system (except the buffing and lifting motor). All electric parts are from famous brand with CE to
 ensure the long time operation of the machine.Use the Taiwan DELTA PLC control system to ensure highÂ
stability and precision.    Â
   Â
12. Control panelÂ
The machine is equipped with DELTA touch screen, the human-computer control surface. The picture and words can directly reflect machine failures and solutions, which makes machine maintenance easier.Â
Â
13.Pressure beam electric lifting system
The rising and falling function of the pressure beam can be started rapidly through the operation screen. The
 separate position indicator can show the rising and falling height.Â
14. Automatic grease lubrication & Automatic oiling:Â
 1.The oil filling structure is controlled by microcomputer and oil filling speed can be defined by the user.Â
    The minimum oil amount alarm is set up.Â
 2.The oil filling structure can add oil for the end trimming moving slider and conveyor guider withinÂ
  set-up time. This can ensure the related parts be lubricated in time, reduce friction and prolong the service  life.
 3.The manual oil filling system for the pre-milling is used for the lubrication of up, down, front and back guide
  rails to prevent service life and ensure work precision.Â
Â
15. Air source processor (triplets)
16.CE optional components
 1) Power break protection device
 2) Central power switch
 3) Protective casing over press roller
 4) CE electrical componentsÂ
Optional:Â
1.Misting station
A) Before pre-milling: Prevent the upper and lower surface from sticking with glue, improve the edge banding effect.Â
B) Before buffing: Improve the cleaning effect of the plate.Â
  Â
2.Pneumatic Tool Alignment SystemÂ
1.Input the new thickness of edgeband,then it can change the edgeband automatically.
2.Position location of cylinder,work with 0.4-3mm edgeband.
3.The manual adjustment is no longer required. The worker only needs to place the corresponding edgebands
 at the entrainment position. Easy to operate.Â
Â
3.Hot air blowers
Brings high gloss shine back to PVC banding after the 3mm scrape station.
Blow after the scrape station, make buffing effect better.
4.Endplay buffing
Control the buffing wheel movement by pneumatic control, prolong buffing wheel service life and improveÂ
buffing effect.Â
5.Caterpillar type pressure beamÂ
Adopt the double-peak caterpillar pressure with high stability. It has large press contact surface and good pressure positioning effect. The belt contacts with wood piece surface can ensure the good pressure
 of panels with different lengths.Â
6.Automatic feeding systemÂ
 Realize edge band feeding by control the press wheels by pneumatic control.Â
7.Fast glue heating
The upper glue box can decrease the gluecarbonization.The fast glue heating system can sense
automatically and heat continuously. It can realize fast glue heating and supply glue continuously.
.
8.Multi-edge band holder
Based on different processing requirements, 2 to 10 different edge bands can be changed automatically.Â
When edge band is used up, the machine will show alarm automatically.Â
9.Dust collection manifold for scraping system.
Catch the wast sawdust caused by scraping.Clean and easy.
 Â
10.PUR Gluing system
Our Workshops
Samach'S Service and dominants:
1: Professional team of techniques study and research, guarantee the Machine latest and improving efficiency.
2.Knowing China and world markets well, offer professional soluttions.
3.Fast market reaction, Â guarantee our partners always in front edge.
4.Supeiror Guarantees,quality of our machine and sell-after services.
5.OEM/ODM are available.
6.Principle: One cooperation, forever partners.
Contact us and Enjoy our Happy Coopperation Together. Thank you for your time ^_^
Top Quality Wood Edge Banding Machine Rfb465jch Woodworking Tool
Model NO.: RFB465JCH
Panel Thinkness: 10-60mm
Min.length panel: 120mm
Min.width panel: 60mm
Manufacturing Principles: Glue Tank Overhead
Customized: Customized
Delivery Time: 25 Days
Type of Edgeband: MDF, Block Board, Solid Wood Board, Polymer Door
Trademark: SAMACH
Transport Package: Wooden Case
Specification: CE Standard
Origin: Shunde, Canton
HS Code: 84659900
Top quality Wood edge banding machine Woodworking tool, size of RFB465jch,is much popular in