Co Powder,Cobalt 6 Powder,Cobalt 12 Powder,Cobalt 21 Powder Luoyang Golden Egret Geotools Co., Ltd , https://www.hvafspray.com
·In May, domestic car recalls exceeded 800,000 Dongben accounted for 15.80%
Recently, according to the recall announcement announced by the official website of the AQSIQ, Geshi Automobile has sorted out the domestic automobile recalls in May 2018. The results show that in May this year, there were 16 announcements concerning car recalls involving 15 automobile companies. For the models, the total number of recalls was 825,846, and the number of recalls increased by 21.16% from 680,000 in April. In April, the recall of more than 600,000 vehicles accounted for 95.33% of the total number of recalls. The Takata problem airbag recall event achieved a “zero recall†in May. The CR-V of the Dongfeng Honda “Oil throttle†problem car was recalled in May, and the number of recalls reached 130,455, accounting for 15.80% of the total recall.
FAW-Volkswagen's recall of 659,049 vehicles became the most recalled brand in May, accounting for 79.80% of the total recall. Mainly related to the Audi A4 Allroad, A5, A6L, A4L and Q5. The main reason for the recall is that there may be two failure modes of the engine auxiliary coolant pump: 1. The auxiliary coolant pump may be blocked by foreign matter and cause overheating; 2. The water vapor in the auxiliary coolant pump may cause short circuit of the internal circuit. As a result, the local temperature of the auxiliary coolant pump is too high and the related parts are ablated. In severe cases, the engine compartment may be ignited, posing a safety hazard.
The defective parts of the recalled vehicles in May mainly include engines, airbags, transmissions, and vehicle controllers. Among them, the Dongfeng Honda “Oil throttle†that has been raging since the beginning of the year has finally yielded results. The recall reached 130,455 vehicles, ranking second only to FAW-Volkswagen. According to the recall announcement, Dongfeng Honda has recalled some of the 2018 models of CR-Vs equipped with 1.5T engines from February 14, 2017 to February 27, 2018, starting from May 22, 2018. Dongfeng Honda will replace the air conditioning control unit and upgrade the FI-ECU software for the vehicles within the scope of the recall. At the same time, replace the radiator water pipe assembly and upgrade the TCU software for the vehicle equipped with the CVT gearbox to prevent the oil level from increasing and eliminate the safety hazard. . At the same time, when the recall is implemented, the engine oil and oil filter are replaced freely for the vehicles within the target range, and the engine cleaner is added.
It is understood that the recall of Dongfeng Honda was carried out under the circumstances of the start of the defect investigation by the State Administration of Market Supervision. For some time, the Defective Product Management Center of the State Administration of Markets has received complaints from consumers about this issue. After receiving the complaint, the State Administration of Market Supervision immediately deployed the Defective Product Management Center to conduct a defect investigation and assessment of the above issues. Affected by the investigation, Dongfeng Honda Automobile Co., Ltd. decided to take recall measures to eliminate potential safety hazards. The State Administration of Small Markets said that it will continue to organize the Defective Product Management Center to conduct key supervision and evaluation of the measures taken in this recall, and requested Dongfeng Honda Automobile Co., Ltd. to improve the recall completion rate in a highly responsible attitude towards consumers. Strengthen the monitoring of recalled vehicles and effectively protect consumer rights.
According to the specific situation, Geshi Automobile conducted comprehensive statistics according to the data recalled by the AQSIQ.
Recall, car recall, May car recall
Attachment: Details of domestic car recalls in May (according to the order of batch recalls)
1. FAW-Volkswagen recalls Audi A4 Allroad, A5, A6L, A4L and Q5 for a total of 659,049 vehicles
Recall range:
Since June 6, 2018, the following vehicles have been recalled, totaling 659,049 vehicles.
(I) FAW-Volkswagen Automotive Co., Ltd. imported a total of 20,278 Audi A4 Allroads and the 2012-2014 Audi A5 cars from November 7, 2011 to November 8, 2013.
(II) Some of the 2012-2015 Audi A6L and 2013-2014 Audi A4L and Audi Q5 vehicles produced by FAW-Volkswagen Automotive Co., Ltd. from May 3, 2011 to January 17, 2016, totaling 638,771 vehicles.
Reason for recall:
There may be two failure modes for the engine-assisted coolant pump in some vehicles within the scope of this recall: 1. The auxiliary coolant pump may be blocked by foreign matter and cause overheating; 2. The water vapor in the auxiliary coolant pump may cause short circuit of the internal circuit. As a result, the local temperature of the auxiliary coolant pump is too high and the related parts are ablated. In severe cases, the engine compartment may be ignited, posing a safety hazard.
solution:
FAW-Volkswagen Automotive Co., Ltd. will entrust the Audi franchisee to replace the improved auxiliary coolant pump for the vehicles within the recall range in three batches according to the plan to eliminate safety hazards.
2. Dongfeng Honda recalled Siwei (CR-V) 130,455 vehicles
Recall range:
Since May 22, 2018, a total of 130,455 CR-V vehicles equipped with 1.5T engines, which were produced from February 14, 2017 to February 27, 2018, were recalled.
Reason for recall:
Due to design reasons, some vehicles in this recall range will increase the engine oil level when the vehicle continues to travel in a low temperature environment for a short distance. When the oil level increases to a certain level, the engine fault indicator will light up. Continuous operation of the vehicle in the state may cause engine damage and pose a safety hazard.
solution:
Dongfeng Honda Automobile Co., Ltd. will replace the air conditioning control unit and upgrade the FI-ECU software for the vehicles within the scope of the recall, and replace the radiator lower water pipe assembly and upgrade the TCU software for the vehicle equipped with the CVT gearbox to suppress the increase of the oil level. Eliminate security risks.
3. Dongfeng Motor recalled 13,128 Dongfeng Fengshen new AX7
Recall range:
Since May 18, 2018, a total of 13,128 vehicles have been recalled for the Dongfeng Fengshen New AX7 cars produced between October 18, 2017 and March 9, 2018.
Reason for recall:
Due to the manufacturer's manufacturing reasons, some of the vehicles in the scope of the recall have defects in the press-fit process of the rear shell seal of the brake vacuum booster assembly. There may be cases where the brake hydraulic shock causes deformation and disengagement of the seal ring skeleton. In extreme cases, the vehicle may have a brake drag and an acceleration weakness, which may present a safety hazard.
solution:
Dongfeng Passenger Vehicle Co., Ltd. will freely inspect vehicles within the recall range and replace defective vacuum boosters with improved vacuum booster assemblies to eliminate safety hazards.
4. FAW Group recalled 8,620 Pentium X40
Recall range:
Since May 22, 2018, a total of 8,620 Pentium X40 passenger cars, which were produced between October 27, 2017 and April 26, 2018, were recalled.
Reason for recall:
In the vehicle within the scope of this recall, due to the flaws in the vehicle controller program, after using the remote function of the mobile phone, the vehicle may be abnormally extinguished during driving. In extreme conditions, there is a risk of causing an accident in the vehicle, and there is a safety hazard.
solution:
China FAW Group Co., Ltd. entrusted FAW Car Co., Ltd. to freely inspect and upgrade the vehicle controller program for vehicles within the scope of the recall to eliminate potential safety hazards.
5. Jiangling Motors recalled 7,180 Jiangling Ford new generations
Recall range:
Since May 5, 2018, a total of 7,180 vehicles have been recalled for the production of some Jiangling Ford new generations of Transit cars from August 1, 2015 to July 31, 2016.
Reason for recall:
Some vehicles in the scope of this recall, because the operating staff did not use the tooling to ensure the clearance between the crankshaft position sensor and the flywheel when assembling the engine, causing the crankshaft position sensor of the individual vehicle to contact and wear the flywheel, resulting in the inability to read the flywheel signal, the engine fault light would Lighting, in extreme cases, may cause the engine to stall during driving, posing a safety hazard.
solution:
Jiangling Motors Co., Ltd. will check and replace the crankshaft position sensor for vehicles within the scope of the recall to eliminate safety hazards.
6. Alfa Romeo (Shanghai) recalls 2,799 units of Steve
Recall range:
Since May 18, 2018, some of the imported 2017 and 2018 Alfa Romeo stelvio cars were recalled from March 3, 2017 to January 25, 2018. According to the company's statistics, there are 2,799 vehicles in mainland China.
Reason for recall:
The vehicle within the scope of this recall is not properly controlled due to the sealing process in the production process. The wiring harness of the body control module (BCM) or the BCM and the body A-pillar may be damaged due to the influent; the same batch of vehicles is improperly controlled due to the sealing process in the production, the electric tail The harness interface and the electric tailgate switch button in the door cover may be damaged by water seepage.
solution:
Alfa Romeo will perform free sealing optimization for the body control module (BCM) involving the recalled vehicle and the wiring harness at the junction of the BCM and the body A-pillar, as well as the inside of the electric tailgate cover to eliminate defects. Stock vehicles will also be sold after the elimination of hidden dangers.
7. Tianjin FAW Toyota, Toyota (China) recalled Corolla (hybrid version) and Lexus RX total 1,726 units
Recall range:
Toyota Motor (China) Investment Co., Ltd. has expanded the recall of the following vehicles, totaling 1,726 vehicles, as follows:
(1) Tianjin FAW Toyota Motor Co., Ltd. recalled the number of Corolla (hybrid version) vehicles produced from January 16, 2016 to February 3, 2016, starting from May 28, 2018.
(II) Toyota Motor (China) Investment Co., Ltd. recalled the Lexus RX vehicles produced from October 22, 2015 to October 29, 2015, starting from July 1, 2018.
Reason for recall:
In some vehicles within the scope of the recall, the airbag control system is equipped with an error sensor of the problem batch. The production conditions of the IC chip in the batch acceleration sensor are not appropriate, resulting in possible disconnection of some IC chips during the use of the vehicle. As a result, the air bag warning light is turned on, and the air bag cannot be deployed normally, posing a safety hazard.
solution:
Tianjin FAW Toyota Motor Co., Ltd. and Toyota Motor (China) Investment Co., Ltd. will check the production number of the airbag acceleration sensor assembled in the vehicle within the recall range, and replace the accelerometers belonging to the problem batch with qualified parts for free. To eliminate security risks.
8. Ford (China) recalls 1,177 Ford F-150
Recall range:
Due to the safety hazard of the transmission shift cable fixing device, from May 24, 2018, 1,177 2018 imported Ford Fs will be recalled from June 6, 2017 to November 25, 2017 (inclusive). -150 Raptor car.
Reason for recall:
The reason for this recall is that the clips that are fixed to the transmission on the shifting cables of some affected vehicles may not be properly installed. With long-running, a clip that is not properly installed or disengaged may cause the driver to not engage in the correct gear. In this case, when the driver hangs in the P position and stops the vehicle, the instrument panel will not be able to warn that the vehicle is not properly engaged in the gear. If the parking brake is not applied, the vehicle may accidentally move in some cases, and there is safety. Hidden dangers.
solution:
Ford China's authorized dealers will check whether the shift cable clamps are correctly installed for the vehicles within the recall range, and adjust the cables and fix the clamps according to the inspection conditions to eliminate hidden dangers.
9. Beijing Benz recalled E-class 860 vehicles
Recall range:
Since May 25, 2018, a total of 860 E-class cars will be recalled from July 12, 2016 to June 22, 2017.
Reason for recall:
On the long-wheelbase E-class vehicle partially equipped with the rear side airbag in the recall range, the main harness may be squeezed by the rear side airbag bracket and cause the harness to be damaged. Once the harness is broken, some of the vehicle's functions will be affected. If the power of the fuel pump is interrupted, the vehicle will lose power; if the harness responsible for the side curtain, side airbag or rear belt tensioner is damaged, the relevant protection function will be affected; if the harness is short-circuited, it will not be excluded. The risk of fire is a safety hazard.
solution:
Beijing Benz Automobile Co., Ltd. will put felt on the side airbag bracket of the vehicle within the recall range to avoid contact between the bracket and the harness, and check the harness, and if it is damaged, repair it to eliminate the safety hazard.
10. Suzuki (China) recalled 305 Kaiser West
Recall range:
Since July 1, 2018, some of the imported Kaiser West cars will be recalled from 2012 to 2015, and the production date will be from November 16, 2012 to December 15, 2015. According to the company's statistics, there are 305 vehicles involved in mainland China.
Reason for recall:
The reason for this recall is that the circuit board of the CVT controller is equipped with a resistor element. Due to the abnormality of the resistor element, the solenoid valve that regulates the CVT oil pressure will not work properly, causing the oil pressure to increase the oil temperature. Raising, triggering the operation of the CVT protection mechanism may eventually lead to a reduction in the speed of the vehicle during the driving process and acceleration difficulties, and there are potential safety hazards.
solution:
Suzuki (China) Investment Co., Ltd. will replace the improved CVT controller for vehicles within the recall range to eliminate safety hazards.
11. Anhui Jianghuai recalled 286 trucks
Recall range:
Since May 10, 2018, some Jianghuai trucks have been recalled, involving a total of 286 vehicles. details as follows:
(1) A total of 191 vehicles were produced in the period from May 2014 to January 2017.
(II) A total of 31 Jianghuai trucks produced between January 2016 and September 2016.
(3) A total of 42 Jianghuai trucks produced between July 2016 and March 2017.
(4) A total of 22 Jianghuai trucks produced between February 2016 and February 2017.
Reason for recall:
Some vehicles in the above range (1) are not standardized due to the reflective marking, and there is a deviation between the reflective range and the area, which does not meet the requirements of relevant standards. There is a safety hazard during night driving.
Due to the manufacturer's manufacturing problems, some of the vehicles in the above range (2) do not meet the requirements of the relevant standards. When the vehicle collides, it may not be effective to protect it, and there are potential safety hazards.
Some vehicles in the above range (3) are not equipped with position lights due to manufacturing problems. If the nighttime or road lighting conditions are poor, the vehicle outline may not be displayed, and the requirements of relevant standards may not be met, posing a safety hazard.
Some vehicles in the above range (4) are not equipped with the tail sign board due to the manufacturer's manufacturing problems. The vehicle has a reflective range deviation, which does not meet the requirements of relevant standards, and there are potential safety hazards.
solution:
For the above scope (1) Anhui Jianghuai Automobile Group Co., Ltd. inspects the vehicles within the scope of the recall, and replenishes or reattaches the reflective signs for free to eliminate potential safety hazards.
For the above scope (2) Anhui Jianghuai Automobile Group Co., Ltd. inspects the vehicles within the recall range and replaces the protective devices that meet the standard requirements free of charge to eliminate potential safety hazards.
For the above scope (3) Anhui Jianghuai Automobile Group Co., Ltd. inspected the vehicles within the scope of the recall, and installed the position lights free of charge to eliminate potential safety hazards.
For the above scope (4) Anhui Jianghuai Automobile Group Co., Ltd. inspected the vehicles within the scope of the recall and installed the tail sign board free of charge to eliminate potential safety hazards.
12. Shenlong Automobile recalls 141 cars of Citroen C4 Picasso
Recall range:
From May 31, 2018, some imported Citroen C4 Picasso series cars will be recalled from January 18, 2017 to April 6, 2017. According to the company's statistics, a total of 141 vehicles were involved.
Reason for recall:
Some vehicles in this recall range may not be able to adhere to the inner and outer plates of the hood due to the position and width of the glass glue on the inner and outer plates of the engine hood, which may cause the hood to shake and deform. In extreme cases, the inner and outer plates of the hood may be degummed and the outer cover of the hood may fall off, posing a safety hazard.
solution:
Shenlong Automobile Co., Ltd. will carry out free maintenance for the vehicles within the scope of the recall. In accordance with the specifications, glass glue will be added between the inner and outer panels of the hood to eliminate potential safety hazards.
13. Dongfeng Motor recalled 65 sets of 65 meters for kindergarten students
Recall range:
Since May 22, 2018, a total of 65 school buses for 6-meter-long children, which were produced from March 31, 2015 to November 1, 2016, were recalled.
Reason for recall:
In the scope of this recall, some of the school bus's side-opening safety doors are turned over without a description of the seat, resulting in the user not knowing how to operate the flip seat. In the case of not flipping the seat, the safety passage width at the safety door is less than 300 mm, which poses a safety hazard.
solution:
Dongfeng Motor Co., Ltd. will provide free training for users of vehicles within the scope of the recall, instructing users to use the flip seat correctly; and attaching the instruction mark to the flip seat to eliminate safety hazards.
14. Yangzhou Yaxing Bus recalled 51 cars of Yaxing brand YBL6121H1QP
Recall range:
From May 15th, 2018, the YBL6121H1QP passenger car produced from November 1, 2015 to March 31, 2018 (including) will be recalled, a total of 51 vehicles.
Reason for recall:
In the vehicle within the scope of this recall, due to the matching degree between the steering trapezoidal mechanism of the vehicle and the steering axle, the steering force does not conform to the national mandatory standard GB17675-1999 "Automobile steering system" during the full-load state of the vehicle. The basic requirements of "3.9 with the help of steering, but the steering force should be less than 588N", there is a safety hazard.
solution:
Yangzhou Yaxing Bus Co., Ltd. will replace the modified steering axle assembly with the trapezoidal mechanism for the vehicles within the recall range to eliminate safety hazards.
15. Porsche (China) recalls 2 Macan
Recall range:
From May 30, 2018, the 2018 Macan will be recalled from January 22, 2018 to January 23, 2018. According to statistics, a total of 2 vehicles are involved.
Reason for recall:
The terminal resistance of the gateway control unit of the vehicle within this recall may not be properly soldered, resulting in interruption of communication between different control units of the vehicle. The various error messages are displayed in the combination meter. In extreme cases, the handling performance of the vehicle and some protective functions required after the collision of the vehicle may be affected, posing a safety hazard.
solution:
Porsche (China) Automobile Sales Co., Ltd. will entrust Porsche Authorized Service Centers across the country to replace qualified vehicle control units for free vehicles within the scope of the recall to eliminate potential safety hazards.
16. Ford (China) recalls 2 Ford F-150 Raptor and Ford Mustang
Recall range:
From May 18, 2018, the 2017 imported Ford F-150 Raptor model will be recalled, and the 2018 Ford Mustang 2.3T performance version will be recalled.
Reason for recall:
The reason for this recall is that due to the instability of the automatic transmission assembly system, the insertion steps of the parking pawl guide sleeve pins on some affected vehicles may be omitted and not installed. If the transmission is used repeatedly in the absence of the pinning, the parking function may be lost, even if the gear and the dashboard indicate that the vehicle has been engaged in the P position; when the driver stops the vehicle, the instrument panel will not be able to warn that the vehicle is not properly engaged in the P position. If the parking brake is not applied, the vehicle may be accidentally moved under extreme conditions, posing a safety hazard.
solution:
Ford China's authorized dealers will check the transmission parking pawl guide sleeve pin for missing vehicles and install the pin on demand to eliminate hidden dangers.