I believe that the majority of users of the sealing machine is not unfamiliar to the continuous sealing machine, continuous sealing machine user friends is not in the process of using a continuous sealing machine often have some failure? Especially when you urgently need to use a continuous sealing machine, the continuous sealing machine suddenly fails and there is no warning, seriously affecting our work. At this time, we should learn to inspect ourselves and quickly solve the problem of continuous sealer maintenance. The following molding and sealing machine series teach you “Five steps to teach you to quickly repair continuous sealing machineâ€. You must read it carefully because it can help you! Five steps to teach you how to quickly repair a continuous sealing machine continuous sealing machine method, method one: Continuous sealing machine picture The above points are the years of experience of Zhu Heng Xiao Bian, and it should be able to meet the requirements of your work. I believe there is a problem that can help you and you can build a technical relationship with Heng Heng! Readers of this article also read:
This series of equipment can regenerate various types of activated carbon such as coal, wood, nut shell, mineral (petroleum), or powder, granule, column, or primary, extruded, and re-formed activated carbon, according to the characteristics of activated carbon fire method regeneration treatment , This series of equipment is equipped with unique flue gas treatment equipment to ensure the green and environmental protection of the activated carbon fire method regeneration process.
The device has the following characteristics:
1.Wide application field: the device can regenate various types of activated carbonon by adjusting the angle and rotational speed of furnace pipe.
2.Regeneration activated carbon in the oven retention time 40 minutes, which is applicable to the regeneration levelofall kinds of grain particles, for coal activated carbon also has good regeneration effect.
3.High degree of automation:the device operation achieves automatic control,with man-machine interface+Intelligent instrument control,reduces the operating workers and the labor intensity is low.
4.High recovery rate of Iodine value:basically returned to a new carbon levels above 90%.
5.Low carbon loss:≤1-2%(Coal carbon)But slightly higher than the JHR-O series activated carbon fuel diesel reclamation equipment
6.Easy installation, covers an area slightly larger, but the small space height requirements, large installed power.
Long service life:The core components furnace tube using thick wall (10 mm thick) 1200 ℃ high temperature resistance, corrosion resistant special stainless steel pipe.
Carbon Regeneration Kiln,Rotary Kiln Services,Carbon Regeneration Process,Chemical Regeneration Of Activated Carbon Changchun Gold Research Institute Co.LTD , https://www.changchunmachine.com
1, first check your continuous sealing machine line is connected, is there a line signal line short circuit or open circuit, as well as welding whether there is a phenomenon of virtual welding.
Fast maintenance of continuous sealing machine method, method two:
1, then check your voltage, if the voltage is not enough, it is easy to cause, can not normally use the boot, the value of instability, on-line beat. When using logic pens and oscilloscopes to detect signals, be careful not to make the probe contact two at the same time
2. Measure the pin, because the essence of this situation is to form a short circuit under power.
Fast maintenance of continuous sealing machine method, method 3:
1. When using the multimeter's ohmic block, remember not to measure with electricity. When detecting the filter capacitor in the power supply of the continuous sealing machine, electrolysis should be first
2. The positive and negative electrodes of the container should be short-circuited, and do not use the lead line instead of the lead to discharge the capacitor, because it is easy to blow the core wire. A 220-volt, 50-watt light bulb with a cap lead can be taken and connected at both ends of the capacitor. At the moment of discharge, the bulb will flash.
Fast maintenance of continuous sealing machine method, method four:
1. When measuring the parameters of each point, you can use ordinary hand-sewing needles to weld the pen on the multimeter so that the points can be directly measured by piercing the paint layer without peeling off the paint layer in a large area. This will cause oxidation of the copper foil.
Rapid maintenance of continuous sealing machine method, method 5:
1. It is necessary for the circuit board's circuit multimeter to measure whether each point is smooth when the maintenance of the wet environment is faulty.
2. Because the main fault in this case is the corrosion of copper foil. For circuit boards that are corrosive, we can use 95% industrial alcohol to clean and wipe, so as not to cause corrosion of the larger mask.
