Domestic large vertical centrifugal pump in operation, there vibration, often up and down the bearing fever, damage, and even pump shaft and bearing connection parts wear. Pump instability, affecting the normal water supply, the need for its damping control. Xiamen Water Group Water Company pumping station Jiangdong pumping station designed daily water supply capacity of 500000 m 3 , a total of six vertical centrifugal pumps installed, of which two imported pumps, four domestic pump. Domestic pump model 28SLA-10, flow Q = 4700m 3 / h, head H = 90m, speed n = 994rpm. Water pump in operation, there is vibration, often up and down the bearing fever, damage, and even pump shaft and bearing connection parts wear. Pump instability, affecting the normal water supply, the need for its damping control. First, the pump vibration analysis 1, domestic vertical pump 28SLA-10 is a direct transformation from the horizontal pump. The vertical height between the motor base and the pump base is 4.3m and the drive shaft weighs 3t. Compared with the horizontal pump, it adds a length of 3752mm diameter 140mm intermediate drive shaft. In the structure, in addition to the middle drive shaft with a bearing, without any modification (Figure 1). The four pumps long-term operating pressure of 0.7 ~ 0.85MPa. In the high head, flow conditions, such a high center of gravity, high-quality system of high-speed rotation, the centrifugal force is great, will cause greater vibration of the unit. Coupled stent and pump out of the water connection stiffness is not enough, resulting in a large displacement of the pump and the connector. Displacement of the pump during operation results in a change in the bearing condition of the bearing. As the vibration increases, it is easy to generate heat. If the correction of displacement pump to improve bearing stress conditions, can reduce the vibration of the system. Install a bearing on the middle drive shaft In the running state of the pump, use the dial indicator to measure the maximum displacement of each point along the water inlet and outlet. The results are shown in the following table (unit: mm) Water pump displacement measurement table It can be seen, the maximum displacement of the pump bearing A point F, the smallest pipeline F point. 2, rigid connection between pump and drive shaft. Due to manufacturing and installation reasons, the pump shaft is concentric with the drive shaft during operation, causing the pump to vibrate. The vibrations generated by motors, transmission shafts and other sources are also directly transmitted to the pump to form a superposition of vibrations to further increase the vibration of the pump. In addition, this rigid connection to increase the water pump bearing the external force, resulting in easy to heat the bearing, affecting the pump shaft. Second, the transformation of the situation For the above reasons, we have taken the following two steps to transform. 1, to strengthen the pipeline stiffness. Taking into account the more difficult for the pump to strengthen, take the outlet pipe in the pump welding "stiffener" approach. Along the direction of inlet and outlet water, flanges at both ends of the connection pipe between the outlet pipe and outlet valve at the outlet of the water pump are welded with 8 steel plates with a thickness of 32mm and a width of 100mm. Increase the stiffness of the steel pipe to reduce the amount of deformation, resistance to pump displacement. After measuring, stiffened, the displacement of pump A point dropped to 0.35mm. 2, the transformation of the transmission system. In order to reduce the motor, the vibration of the transmission shaft is transmitted to the water pump, and the rigid connection between the water pump and the transmission shaft is changed to a flexible connection. Use GB4323-84 elastic sleeve pin coupling, the maximum compensation displacement of 0.6mm, compensation angle of 1 ° 30'. In this way, the vibration of the motor and drive shaft can be compensated by the flexible coupling, and the vibration can not be directly transmitted to the pump. Third, the transformation results After the transformation, the vibration of the pump was reduced to 1.48cm / s from 4.3cm / s before the transformation. According to the vibration intensity standard ISO2372-1974 can determine that the pump is running in the best area. At the same time, the pump runs smoothly, the bearings only need normal maintenance, and the shaft of the pump is abraded, indicating that the transformation is successful.
Volatile silicone oil includes Disiloxane 0.65cst, Trisiloxane 1cst, Dimethicone 1.5 and 2cst, Caprylyl Methicone, Methyl Trimethicone and so on.
Low viscosity silicone oil includes Dimethicone 5cst, 6cst, 10cst and so on.
Modified silicone oil is one silicone emulsifier, includes PEG-12 Dimethicone, PEG-10 Dimethicone, Bishydroxyethoxypropyl Dimethicone and so on.
Silicone elastomer includes Dimethicone (and) Dimethicone / Vinyl Dimethicone Crosspolymer, Dimethicone (and) Dimethicone / Vinyl Dimethicone Crosspolymer,
Dimethicone (and) PEG-10 Dimethicone / Vinyl Dimethicone Crosspolymer, Dimethicone (and) PEG-10 Dimethicone / Vinyl Dimethicone Crosspolymer, Cyclopentasiloxane (and) Dimethicone Crosspolymer, Cyclopentasiloxane (and) Dimethicone Crosspolymer (and) Silica and so on.
Silicone resin is a large molecular weight silicone powder that can be used as a film forming agent to form a long-lasting polymer film with excellent migration resistance and elution resistance, improving the durability of the product after use. which is different Trimethylsiloxysilicate and are used in non-stick cup lipstick, lip glaze, BB cream, liquid foundation, liquid eyeliner, mascara and other fields, can quickly form film, to achieve the ideal makeup holding effect.
Silicone oil for hair care is Used in the formulation of essential oil for hair care, it can form a film on damaged hair, improve carding and long-term moisturizing.
which has Dimethicone (and) Dimethiconol, Cyclopentasiloxane (and) Dimethicone , Phenyl Trimethicone and so on.
Oil soluble silicone wax Can produce closed moisturizing effect, wear light, good skin affinity, which can Help inorganic fillers disperse, cooperate to increase the SPF of physical sunscreen, improve gloss. also has Good compatibility with other oils and waxes, hot and cold evenly. which includes Cetyl Dimethicone, Stearyl Dimethicone (and) Octadecene and so on.
silicone oil, Silicone Resin, silicone elastomer, silicone wax Luckypower Tech , https://www.czluckypowertech.com position A B C D E F Running displacement 0.75 0.72 0.56 0.68 0.30 0.08